Showing results: 16 - 30 of 240 items found.
-
SCR ELEKTRONIKS
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
SCR ELEKTRONIKS
The test system is a special version of the thermal + Magnetic test test system. The single power source able to deliver either thermal or magnetic test parameters set on the PC by the user.
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
IPETRONIK GmbH
Our IPEtec test bench engineering business unit plans and provides customized test bench solutions for the development and validation of automotive AC components. We offer a full range of test benches and media-supply modules for the automotive developer’s thermal management needs. Moreover, we support the development of new cooling systems for hybrid power trains, for battery and engine cooling. New hybrid power trains are opening up additional fields of heat-pump technology development aimed at optimizing the energy balance of automotive air conditioning.
-
-
CX-DWC -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884-1 Uses: It is used to evaluate the impact resistance of electrical accessories under low temperature conditions, and also to evaluate the low temperature impact resistance of wire and cable.
-
IEC60884 fig38 -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig38 thermal compression test device for plug testingUsed to evaluate the pressure resistance of electrical accessories and wall mounted mounting boxes under heatStandard: GB2099.1-2008 Articles 24.19 and 25.4 and Figure 38, IEC60884-1 Figure 38, etc.
-
SCR ELEKTRONIKS
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
dbSAFE TSE -
DVTest Inc.
Compatible with all platforms of temperature forcing units and thanks to the DVTEST “waveguide” technology; isolation performance will not be impacted. The temperature range of the units will be -90°C to +220°C.
-
Teledyne LeCroy
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
PXP-500A -
Teledyne LeCroy
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
GT9000 -
Guide Technology, Inc.
GT9000 is a scalable 2 to 10 channelsBench-Top CTIA and/or TIC Test Platformwith 10” touch-screen-display (iPhone quality), integrated GUI with Touch, Ethernet, WiFi and/or wireless keyboard & mouse.
-
GT9000P-USB3 -
Guide Technology, Inc.
A 2 channel Portable “CTIA” and/or “TIC” Test Platform controlled by USB3
-
GT9000R -
Guide Technology, Inc.
GT9000R is a scalable 2 to 24 channels 19”Rack-Mount CTIA and/or TIC Test Platformwith integrated GUI, Ethernet, Wi-Fi and/orwireless keyboard & mouse.